Metal-plastic hybrid assemblies: When two technologies take on a function

23rd July 2026

Why metal and pla­s­tic should be con­side­red tog­e­ther

Anyo­ne who wants to have metal parts spray­ed needs a part­ner who can design the metal part, the pla­s­tic tool and the assem­bly tog­e­ther. KOMOS GmbH from Bür­gel (Thu­rin­gia) manu­fac­tures stam­ping and tur­ning parts its­elf, sprays them in its own injec­tion mol­ding pro­cess, and assem­bles and tests com­ple­te hybrid assem­blies – in bat­ches of 100 to 50,000 units.

Metal often per­forms elec­tri­cal or mecha­ni­cal func­tions in tech­ni­cal pro­ducts. For exam­p­le, pla­s­tic pro­vi­des insu­la­ti­on, posi­tio­ning, pro­tec­tion, or gui­dance. Only when both mate­ri­als are spe­ci­fi­cal­ly com­bi­ned with each other does a func­tion­al unit result.

Such metal-pla­s­tic hybrid assem­blies are used, among other things, in elec­tri­cal engi­nee­ring, medi­cal tech­no­lo­gy, sen­sors, and in the manu­fac­tu­re of equip­ment.

Spray­ing or assembling metal parts?

The­re are dif­fe­rent tech­ni­cal methods for manu­fac­tu­ring hybrid assem­blies.

In insert mol­ding, metal­lic inserts are joi­n­ed direct­ly to the pla­s­tic during the injec­tion mol­ding pro­cess. Alter­na­tively, metal and pla­s­tic parts can be manu­fac­tu­red sepa­ra­te­ly and then joi­n­ed tog­e­ther.

Spray­ing metal parts is usual­ly advi­sa­ble when:

  • hig­her volu­mes are plan­ned,
  • Iso­la­ti­on or tight­ness are par­ti­cu­lar­ly important,
  • The metal part must fit very pre­cis­e­ly in posi­ti­on.

Sepa­ra­te­ly pro­du­cing and assembling is usual­ly advi­sa­ble when:

  • smal­ler series are plan­ned,
  • Tool cos­ts should remain low,
  • Fur­ther chan­ges to the design are still expec­ted.

Which solu­ti­on is sui­ta­ble in a par­ti­cu­lar case depends on seve­ral fac­tors:

  • Requi­re­ments for elec­tri­cal insu­la­ti­on
  • mecha­ni­cal loads and tole­ran­ces
  • Geo­me­try of the com­pon­ents
  • Plan­ned quan­ti­ties
  • Tool cos­ts and chan­ge fle­xi­bi­li­ty
  • Requi­re­ments for assem­bly and test­ing

Ear­ly con­side­ra­ti­on of the­se rela­ti­onships can avo­id sub­se­quent tool chan­ges, addi­tio­nal assem­bly steps, and unneces­sa­ry cos­ts.

Mul­ti­ple manu­fac­tu­ring pro­ces­ses in one loca­ti­on

KOMOS com­bi­nes the pro­duc­tion of stam­ping and tur­ning parts (Stam­ping and ben­ding – KOMOS) using injec­tion mol­ding of pla­s­tic mate­ri­al, fol­lo­wed by assem­bly and test­ing. This allows the indi­vi­du­al com­pon­ents of a hybrid assem­bly to be coor­di­na­ted with one ano­ther.

This beco­mes par­ti­cu­lar­ly inte­res­t­ing when cont­acts, elec­tri­cal wiring or other func­tion­al ele­ments must also be inte­gra­ted along­side the mecha­ni­cal con­nec­tion. Then not only a metal-pla­s­tic part is crea­ted, but a com­ple­te func­tion­al assem­bly.

Eco­no­my beg­ins in the design pha­se

Con­side­ra­ti­on should be given at the design stage to how the assem­bly will be manu­fac­tu­red, assem­bled and tes­ted later on. (R&D / Modu­le deve­lo­p­ment – KOMOS)

A struc­tu­ral­ly simp­le design does not neces­s­a­ri­ly have to be the most eco­no­mic­al seri­al solu­ti­on. What is cru­cial is the inter­play bet­ween too­ling cos­ts, mate­ri­al usa­ge, pro­cess relia­bi­li­ty, and assem­bly cos­ts. This is exact­ly whe­re the inte­gra­ted manu­fac­tu­ring approach from KOMOS comes into play.

You are deve­lo­ping a metal-pla­s­tic assem­bly?

Whe­ther it’s the injec­tion of metal parts, joi­ning, or the com­ple­te inte­gra­ti­on of addi­tio­nal com­pon­ents: We help you find a tech­ni­cal­ly and eco­no­mic­al­ly sui­ta­ble manu­fac­tu­ring solu­ti­on.

Let’s take a look at your hybrid assem­bly tog­e­ther.

Metal part from our pro­duc­tion